გათბობის ქვაბის შეკეთება
Negotiable priceცენტრალური გათბობის შეკეთება, მონტაჟი
Negotiable priceგაზის კალონკის შეკეთება, მონტაჟი
Negotiable priceTips for the Proper Functioning of Heating Systems
Routine system flushing (chemical cleaning): Over the years, scale, rust, and sludge accumulate inside central heating pipes and radiators. This disrupts water circulation, causing the bottom part of the radiators to remain cold, forcing the boiler to work under extra load, and increasing utility bills by 20% to 30%. The system should be flushed using specialized equipment and chemical solutions once every 3 to 4 years. Expansion tank and pressure control: If the pressure in your heating boiler drops frequently, or conversely, rises sharply when the system heats up and discharges water from the safety valve, the cause is an incorrect air pressure level or a damaged membrane inside the expansion tank. Under normal conditions, the pressure in a cold system should be between 1.2 and 1.5 bar. Cleaning the water filters: A mechanical mesh filter (commonly known as a Y-strainer) is always installed under the heating boiler on the return (inlet) pipe. Neglecting it and letting it clog with dust and debris blocks the water flow, causing boiler noise, overheating, and premature failure of the circulation pump. Removing scale from the heat exchanger: Due to the hard water prevalent in the Georgian market, limescale buildup quickly forms inside the boiler's primary and secondary heat exchangers (where hot water is produced). If the boiler shuts down frequently or the domestic hot water temperature fluctuates constantly in the shower (alternating between hot and cold), the heat exchanger needs to be flushed with a specialized acidic solution. Balancing underfloor heating manifolds: Underfloor heating systems (manifolds/headers) require precise hydraulic regulation via flow meters (linear regulators). Improper balancing will cause rooms closest to the boiler to overheat, while more distant zones remain cold. 💡 Meet winter warmly and peacefully: Find certified heating technicians, authorized central heating boiler repair masters, and underfloor heating specialists on the platform: services.ss.ge
ცენტრალური გათბობის მონტაჟი/შეკეთება
Negotiable priceნებისმიერი გათბობის ქვაბის შეკეთება
Negotiable priceკალონკების,გათბობების სისტემებისა და კარმის ხელოსანი
Negotiable priceგათბობის სისტემების მონტაჟი, შეკეთება
Negotiable priceგათბობის სისტემების ხელოსანი
Negotiable priceგამორეცხვა: გათბობის ქვაბის, მილების და ბატარეების
Negotiable priceცენტრალური ქვაბის შეფუთვა სენდვიჩით.
Negotiable priceცენტრალური გათბობის ქვაბების შეკეთება
30 ₾ - Fromგათბობის სისტემების სერვისი
Negotiable priceცენტრალური გათბობის მონტაჟი
Negotiable priceFrequently Asked Questions - Heating Systems
A condensing boiler is a modern, highly efficient appliance that recovers and uses the latent heat from water vapor within the exhaust gases to reheat the system. It consumes 15% to 20% less natural gas compared to a conventional boiler. However, to maximize its efficiency, it requires a low-temperature system setup (such as underfloor heating or oversized radiators, where the water temperature does not exceed 50°C).
Modern heating boilers are equipped with highly sensitive electronic control boards. Voltage fluctuations or sudden power drops are the leading causes of these expensive boards burning out. A quality stabilizer protects the appliance from electrical damage, while a UPS ensures the boiler keeps running during blackouts, preventing the system from freezing in winter.
If a radiator is partially cold (for example, the upper corner fails to heat up) or you hear a gurgling water sound coming from the pipes when the system is running, it means air is trapped in the system. Bleeding is done via the special Mayevsky air vent valve located at the top end of the radiator — use a radiator key or a flathead screwdriver to gently loosen the valve until water, instead of air, begins to flow out. After this procedure, make sure to check and top up the pressure in the boiler.